- #Logitech harmony soundgraph imon how to
- #Logitech harmony soundgraph imon install
- #Logitech harmony soundgraph imon download
If you have an IR transmitter (I didn't), go ahead and select that on the next screen You'll get a configuration window within your terminal window. In the same terminal window, perform the following:: Then you want to reinstall LIRC so that we can have the configuration settings come up and we can configure lIRC. Open up a terminal, and type the following in: Un-install LIRC so that any errors that were going on before won't come up. The volume knob on the Antec Case should work right out of the box. So just follow the below directions to get you up and running.
#Logitech harmony soundgraph imon install
If you're doing a fresh install of Mythbuntu 10.10, there is no configuration to set what /dev/input/eventX device you want to utilize. It also includes instructions to get the LCD up and running. Note that I used Mythbuntu 10.10, but any type of Ubuntu 10.10 should also work with this setup instructions.
#Logitech harmony soundgraph imon how to
There is also a section describing how to setup a Logitech Harmony One Universal Remote Controller that works with this setup. This page contains all of the files and information I needed to get my Antec Fusion Case (Black finish, uses the newer iMon LCD 15c2:0038) and it's included Veris RM200 remote working. I used the lircrc file from ’s Harmony 880 wiki page.It has been suggested that this article or section be merged into Imon. In my case, the user ‘mythtv’ runs MythFrontend, so the file is /home/mythtv/.mythtv/lircrc. This requires that an appropriate lircrc file be copied to ~/.mythtv/lircrc. Now that LIRC knows how to talk to the hardware (step 4), and what the button codes mean (step 5), you have to tell LIRC what virtual keypresses to generate in order to interact with MythTV. # This file should be placed in /etc/nfĮnd remote Step 6: Configure LIRC for MythTV # Microsoft Media Center PC) and the Antec Fusion's iMON PAD Using irrecord to capture button codes, I ended up with this file: # nf file for Harmony 880 (configured to control a For whatever reason, entirely different button codes are sent with my Harmony 880 configured to control a “Microsoft Media PC”. I started out with this nf file, but it’s intended for a true Microsoft Media Center remote. Note that it does not go in /etc/lirc/nf, since lircd seems to only look for /etc/nf. LIRCMD_CONF="/etc/lirc/nf" Step 5: Configure LIRC for the Logitech Harmony 880Ĭopy the correct nf file to /etc/nf. # Default configuration files for your hardware if any # If DEVICE is set to /dev/lirc and devfs is in use /dev/lirc/0 will be # Run "lircd -driver=help" for a list of supported drivers. #Don't start lircmd even if there seems to be a good config file Step 4: Configure LIRC for iMonĬopy an appropriate nf file to /etc/lirc/nf.
#Logitech harmony soundgraph imon download
Step 3: Compile LIRC iMon Supportįollow these instructions to download and compile LIRC for iMon support. They will be listed here when I find my notes. The instructions for compiling LIRC leave out several necessary dependencies. If something like this doesn’t appear in the output, then the USB connector from the front of the case is probably not connected properly. The output of lsusb should contain a line similar to this: Bus 001 Device 003: ID 15c2:ffdc SoundGraph Inc. The LIRC daemon then has to be properly configured so that it loads the correct driver, interacts with the right device, and sends the correct virtual keypresses to MythTV. LIRC has to be configured and compiled to provide this. The lirc_imon module is used to communicate with the iMON PAD. I have an Antec Fusion Black 430 HTPC case, which has a built-in LCD and IR receiver, and I want to control it using my Logitech Harmony 880 programmable remote.
0 kommentar(er)
